Micron Electronics NetFRAME LV2000 Uživatelská příručka Strana 62
- Strana / 102
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Micron Electronics, Inc. 3-25
Chapter 3: Configuring the System
32 Bit I/O Disabled
Enabled
Transfer Mode Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
Secondary Master and Slave
Feature Choices Description
32 Bit I/O Disabled
Enabled
Smart Monitoring Disabled Not available.
Keyboard Features
Feature Choices Description
Num Lock Auto
On
Off
Key Click Disabled
Enabled
Keyboard auto-repeat rate 30/sec
26.7/sec
21.8/sec
18.5/sec
13.3/sec
10/sec
6/sec
2/sec
Keyboard auto-repeat delay 1/4 sec
1/2 sec
3/4 sec
1 sec
Enabling allows 32 bit IDE data
transfers.
This field is informational only for
Type Auto.
Selects the method for moving data
to and from the drive.
This field is informational only for
Type Auto.
Enabling allows 32 bit IDE data
transfers.
This field is informational only
for Type Auto.
Selects power-on state for Num Lock
Enables or disables key click
Selects key repeat rate
Selects delay before key repeat
- NetFRAME 1
- Copyright and Trademarks 2
- Safety Information 3
- Power Supply Warning 4
- Battery Warning 4
- Ergonomic Notice 5
- FCC Information 6
- DECLARATION OF CONFORMITY 7
- Table of Contents 9
- Chapter 1 10
- Setting Up Your System 10
- Unpacking 11
- Getting Started 12
- What You Need 12
- Putting It All Together 12
- Micron Electronics, Inc. 1-5 14
- Figure 1-5. Tower Case-Front 14
- 1-6 Micron Electronics, Inc 15
- Figure 1-6. Tower Case-Rear 15
- Turning Off Your System 16
- Maintenance 17
- Protecting 18
- Backing Up 18
- Removing the System Cover 19
- Micron Electronics, Inc. 1-11 20
- Chapter 2 21
- Overview 22
- System Board 23
- 2-4 Micron Electronics, Inc 24
- Jumper Settings 25
- CMOS Jumper 28
- Password Jumper 28
- Recovery Boot Jumper 28
- CPU Speed Jumper 30
- FRB Timer Enable Jumper 30
- Installing Add-On Peripherals 32
- Add-in Board Slots 33
- DIMM sizes and compatibility 34
- DIMM Modules 35
- Removing DIMM Modules 37
- Chapter 3 38
- Configuring the System 38
- BIOS Setup 39
- When Setup Should Be Run 39
- Power-on Self Test (POST) 40
- When to Run the SCU 42
- Record Your SCU Settings 42
- Six Steps in Using the SCU 44
- Add and Remove Boards 45
- To define an ISA board: 45
- Change Configuration Settings 46
- Advanced Options 46
- Save Configuration 47
- View Switch/Jumper Settings 47
- SCU Utilities 48
- Server Management 56
- Using Setup 57
- If You Cannot Access Setup 58
- How to Enter and Start Setup 58
- Setup Menus 59
- Main Menu 60
- Primary IDE Master and Slave 61
- Secondary Master and Slave 62
- Keyboard Features 62
- Advanced Menu 63
- PCI Configuration 64
- 3-28 Micron Electronics, Inc 65
- Feature Choices Description 65
- Feature Option Description 65
- Micron Electronics, Inc. 3-29 66
- 3-30 Micron Electronics, Inc 67
- Security Menu 68
- 3-32 Micron Electronics, Inc 69
- Server Menu 70
- Server Management Information 71
- Console Redirection 71
- Boot Menu 72
- Hard Drive 73
- Exit Menu 74
- Using SCSI 75
- Main Menu, SCSI 76
- Boot Device Options, SCSI 78
- Exit Menu, SCSI 83
- Installing Video Drivers 84
- Chapter 4 85
- Introduction 86
- System Problems 90
- Hard Disk Problems 93
- POST and Boot Messages 97
- Glossary 98
- C-2 Micron Electronics, Inc 99
- Appendix C: Glossary 100
- C-4 Micron Electronics, Inc 101
- About Device Drivers 102
- WARNING: 102
- Installing the Sound Drivers 102
Tapco pmn manuals
Owner’s manuals and user’s guides for Receivers and Amplifiers Tapco pmn.
We providing 1 pdf manuals Tapco pmn for download free by document types: User Manual
Komentáře k této Příručce